SAE J1100 EPUB

SAE J This standard provides a system of a defined nomenclature to describe vehicle dimensions. A. combination of letters and numerals helps the. This SAE Recommended Practice defines a set of measurements and standard procedures for motor vehicle dimensions. The dimensions are primarily intended . 26 May BY ORDER OF THE EXECUTIVE DIRECTOROffice of the Federal RegisterWashington, Authority of the Code of Federal Regulations.

Author: Mudal Vozahn
Country: Indonesia
Language: English (Spanish)
Genre: Love
Published (Last): 14 February 2007
Pages: 422
PDF File Size: 5.21 Mb
ePub File Size: 1.89 Mb
ISBN: 677-6-89018-594-1
Downloads: 11923
Price: Free* [*Free Regsitration Required]
Uploader: Kebar

See Figures 4 through Any portion of this mm by mm area around the SgRP sze side view below and behind the seat cushion and seat back trim is excluded.

If no arm rest sae j1100 provided at the designated “X” plane, use a height sae j1100 1 80 mm above the SgRP. This sas includes vertical adjustment independent of track travel. PH1 Clutch pedal pad height The Luggage Sae j1100 Lid or access door must close and lock freely without forcing or excessive slamming with all of the luggage in place in the compartment.

SAE J1100: Motor Vehicle Dimensions

L55 Fiducial mark sae j1100. In case of dual wheels, the dimension will be measured to the centerline of tire and wheel assemblies.

Scope— This SAE Recommended Practice defines a uniform set of interior and exterior dimensions for passenger bars, sae j1100 passenger vehicles, and trucks.

See Figure 29 G 2 0. If the seatback is adjustable, use the normal driving and riding position specified by the manufacturer.

Total of all areas. All head restraints shall be in the stowed position and considered part of the seat. S1 Windshield area The lateral Y coordinate location for the Sae j1100 of Foot is mid-width on the shoe at the side view Ball of Foot location.

A minus – dimension indicates the bottom of the eyellipse is located below the sae j1100 of the steering wheel. For any vehicle not trimmed, measure the sheet metal.

H5 SgRP – front to sae j1100 6. GVWR is the value specified by the vehicle manufacturer as the loaded weight of a single vehicle.

L Cargo body overall length 8. For vehicle with more than three seats, specify seat location along with dimension.

Full text of “SAE J Motor Vehicle Dimensions”

H Seat Sae j1100 height – front 6. The limiting structural component shall be designated. A piece from the Standard Luggage Set may be removed to place an H-box in the compartment, provided the removed piece is replaced. Exterior components are projected horizontally to the exterior glazing surface see Figure 3. Each sae j1100 is assigned a code which is composed of a prefix letter denoting the direction sae j1100 type of dimension and a number issued in sequence as required by each prefix letter.

This measurement accounts for adjustments independent of track rise. Has X, Y, Sae j1100 coordinates established relative to the designed vehicle m1100, c. The dash panel is usually the vertical extension of the toe panel. If the area is totally excluded by the seat cushion and seat back trim, measure width to trimmed door or trim surface closest, in side view, to the SgRP.

Establishes the rearmost normal design driving or riding position of each designated seating position which includes consideration of all modes of adjustment, horizontal, vertical, and tilt, in a vehicle, b. SAE invites your written comments sae j1100 suggestions. The standard right and left mirror adjusted for normal driving will be shown unless otherwise noted.

H70 SgRP – front – Z coordinate 6. For heavy-duty trucks, suspension seats will be positioned as specified by the vehicle sae j1100 in the normal sae j1100 position with any fore and aft isolator locked out. Is the reference point employed to position the two-dimensional drafting template with the 95th percentile leg described in SAE J

Author: admin